Buying a constant tension hose clamp is mostly an exercise in filling in six lines correctly: the hose size and range window, the band series, the band and housing material, the screw and washer material, the load rating and the options such as a liner or documentation. Get those six right and the clamp does what its Belleville spring washers are meant to do, which is keep a near-steady squeeze as a hose relaxes, swells and shrinks. Get one wrong, and you have bought an expensive worm gear clamp.
This guide is organised as a purchase specification card. Each line of the card gets a section that explains what to write, what to watch for in a supplier’s datasheet and what the numbers mean. Near the end you will find a copy-paste request-for-quotation template and a short incoming-inspection routine. If you want the physics and history, read what a constant tension hose clamp is first. If you want selection by application, how to choose a constant tension hose clamp covers it, and this article assumes you have decided to buy and now need to specify.
What you are actually buying
A constant tension clamp (also sold as a constant torque clamp) is a worm gear clamp with one extra part: a stack of coned spring washers, called Belleville washers, under the screw. When the hose compresses or contracts, the stack pushes back and the band closes a little. When the hose expands, the stack gives and the band opens a little. Makers describe this as a patented or proprietary mechanism that adjusts the clamp’s diameter to compensate for hose compression set and for expansion and contraction with temperature, which is the language used on truck-parts retail listings.
That extra part is the reason for the extra price, and it is also the part that datasheets are most likely to leave out. When you buy, you are paying for four things working together:
- A band that is wide and smooth enough to load the hose evenly.
- A housing and screw that can turn the band and survive the environment.
- A washer stack that stores and returns load.
- A load rating that tells you how hard it is safe to drive the screw.
The spec card below covers all four.
The six-line specification card
Copy this table into your purchase order or drawing note. Each line has a section later in this guide.
| Line | What you must state | Typical entry | Watch for |
|---|---|---|---|
| 1. Size | Hose OD at the fitting, and the clamp range that holds it mid-range | “2.35 in hose OD, range 1-13/16 to 2-3/4 in” | Ranges that differ between makers |
| 2. Band | Band width and series | “9/16 in standard” or “5/8 in heavy duty” | HD and standard mixed in one quote |
| 3. Band and housing | Material grade | “301 stainless”, “304 stainless” | “Stainless” with no grade |
| 4. Screw and washers | Screw material, drive, washer material | “410 stainless screw, 5/16 in hex” | Zinc-plated screw on a coastal job |
| 5. Load rating | Maximum torque and installation torque | “Rated 70 in-lb, install per maker” | Torque presented as pressure rating |
| 6. Options | Liner, finish, pack size, documents | “Certificate of conformity on request” | Silent on liner |
Line 1: size
Size is the line most buyers already know how to write, so keep it short and tie it to a measurement.
Measure the hose with the fitting inside, then choose the clamp whose range puts that number mid-range. Constant tension clamps are usually sold with a generous range, and some makers advertise an extended adjustment range so fewer part numbers cover a whole fleet. One truck-parts brand states that an extended adjustment range permits fewer stocked parts for complete coverage on its all-stainless constant-torque clamps.
Two buyer notes:
- Ranges are maker-specific. A 2.35 inch hose may fit a clamp from one maker at 57 percent of its range and a similar-looking clamp from another at 88 percent. Always read the printed range for the exact part number. Our constant tension hose clamp size chart shows how to read it.
- Check both ends of the range. Constant tension clamps work best when the washer stack has room to move. A clamp at the extreme of its range may begin with the stack already collapsed, which leaves no reserve.
On the OneTouch range, the standard series runs from 4CT0010 to 4CT0048 in eleven sizes, and the heavy-duty series runs from 4CT175 to 4CT850, with part numbers that appear to encode the nominal diameter in hundredths of an inch and spans up to 8.63 inches. The heavy-duty series comes in an “L” version and an “S” version, covered below. The full range sits in the constant tension clamp category.
Line 2: band width and series
Band width does three jobs. It spreads the load over more hose, it resists cutting into soft hose and it gives the housing more material to hold the screw’s thread. For a given band tension, a wider band means a lower squeeze on the hose, which is gentler but needs more tension to reach the same sealing pressure. Constant tension clamps solve that by being built with a strong band and a spring that stores tension.
Widths you will meet:
| Series | Band width | Where you see it |
|---|---|---|
| Standard | 9/16 in (about 14 mm) | OneTouch 4CT0010 to 4CT0048, Ideal-Tridon Flex-Gear 47 series, Kuriyama |
| Heavy duty | 5/8 in (about 16 mm) | OneTouch 4CT175 to 4CT850, Trident 730 series, Pirtek CTC range at 15.8 mm |
| Extended | Wider, for large hose | Check the maker’s list |
Examples of published widths: Ideal-Tridon’s Flex-Gear 47 series is listed with a 9/16 inch width in 301 stainless, Pirtek’s constant tension range lists 304 stainless with a 15.8 mm band, and Trident’s 730 series uses a 5/8 inch 304 band. For the general effect of width on hose contact, see our note on hose clamp band width.
Buyer rule: write the band width on the order. Do not rely on the part number to imply it, because some suppliers list both widths in one family.
Lines 3 and 4: material, in two parts
A constant tension clamp has more metals than a basic clamp. The band and housing are one pair. The screw is another. The washers are a third, and datasheets almost never state them.
Band and housing
The usual grades are 301 stainless, chosen because it is springy and strong when cold-worked, and 304 stainless, chosen for its general corrosion resistance. Published examples include 301 on the Ideal-Tridon series linked above, 304 on the Trident and Pirtek ranges, and a mix of options on McMaster-Carr, whose constant-tension worm drive listing shows 300 series stainless with a zinc-plated steel screw. OneTouch’s standard and heavy duty clamps use 301 bands and housings on the pages we checked, and the pages do not state a 304 or 316 grade.
Screw
This is where the build quality shows. Three screw materials are common.
| Screw | Where it appears | What it means |
|---|---|---|
| Zinc-plated carbon steel | OneTouch heavy duty “L” series, McMaster 300 series listing | Strong and cheap, corrodes in wet or salty service |
| 410 stainless | OneTouch standard 4CT and heavy duty “S” series | Better than plated, still can rust in salt |
| 300-series stainless | Premium all-stainless builds | Best for corrosion, needs thread care against galling |
The “L” and “S” suffix on OneTouch heavy duty clamps is the screw choice: “L” has a zinc-plated carbon steel screw, and “S” has a 410 stainless screw. If your joint is wet, outdoors or near road salt, specify the stainless-screw version and state it in the order.
Washers
The washers are the heart of the clamp, and their material is rarely printed. Ask. In particular, ask whether they are stainless or plated steel, and whether they are stacked in a way that keeps their nominal travel. For a deeper look at grades, our 304 vs 316 constant tension clamp guide and stainless vs galvanized constant tension clamp comparison cover the choices, and our wider article on why stainless steel is the best material for hose clamps explains how band and screw grades interact.
Line 5: load rating
“Load rating” is the most misunderstood line on a clamp datasheet, because it can mean three different things.
| What the number might be | What it tells you | What it does not tell you |
|---|---|---|
| Maximum torque rating | The most torque the screw and housing should see | How much pressure the joint will hold |
| Installation torque range | The torque to apply when fitting the clamp | A limit for abuse |
| Working pressure | What a joint with this clamp can hold | Almost never published for hose clamps |
A distributor’s technical notes make the key point: torque ratings correspond to the torque rating of the screw and are not an indication of the working pressure of any hose assembly fitted with the clamp, as stated in Dixon’s clamp guide. So when you read “rated 70 in-lb”, read “do not exceed 70 in-lb on the screw”, not “holds 70 psi”.
What published ratings look like
The table below collects published figures so you can see the pattern. They are examples from different makers and sizes, not a standard.
| Example | Band | Size range | Published torque figure |
|---|---|---|---|
| OneTouch standard 4CT | 9/16 in | Standard sizes | 70 in-lb rating, 5/16 in hex |
| OneTouch heavy duty 4CT (L or S) | 5/8 in | Up to 8.63 in | 92 in-lb rating, 3/8 in hex |
| Velvac constant-torque, small size | 9/16 in class | 9/16 to 1-1/16 in | 30 to 70 in-lb, per its listing |
| Velvac constant-torque, larger size | wider | 2-1/4 to 3-1/8 in | 40 to 125 in-lb, per its listing |
| Trident 730 series | 5/8 in | Smaller sizes / larger sizes | 30 to 70 in-lb / 50 to 120 in-lb recommended maximum |
| Kuriyama WGC-CT900 | 9/16 in | 8-1/4 to 9-1/8 in | 90 in-lb suggested installation torque, per its product page |
Notice two patterns. First, ranges for small clamps cluster around 30 to 70 inch-pounds, and larger clamps list higher numbers, because bigger hose needs more tension for the same squeeze. Second, makers differ on whether the figure is a ceiling or a target. That is why the sibling article, constant tension hose clamp torque specifications, goes into how to read the number and how to confirm an install without relying on torque alone.
Buyer rule: write two numbers on the order, the maximum rating and the installation method, for example “install until washers are nearly flat per maker”. Do not write a single torque figure and leave it ambiguous.
Line 6: options and paperwork
The last line collects everything that is not size, band, material or rating.
- Liner. Some constant tension clamps include an extended inner band that covers the worm gear slots to protect soft hose. Velvac’s listing for one series says its extended inner liner covers the slots to protect against extrusions. OneTouch’s constant tension product pages do not mention a liner, so if you need one for silicone, ask before you order.
- Finish. Bright stainless, plain or passivated. Ask if appearance or washdown matters.
- Pack size. Boxes of 10 are common. Fleets and distributors may want bulk packs; our bulk hose clamp buying guide for distributors covers volume ordering.
- Documents. Material certificates, test reports and a certificate of conformity, if your quality system needs them. Our purchase manager’s checklist lists what to ask for.
- Warranty. Some makers state one. For example, Trident’s specification sheet for its 730 series lists a three-year warranty.
- Interchange. If you are replacing an existing brand, ask for a cross-reference. The OneTouch cross-reference tool searches by competitor part number.
Standard or heavy duty? A buyer’s shortcut
Many purchase orders stall on this one question. The short answer is that the choice follows hose size and consequence, not brand.
| Question | If yes | If no |
|---|---|---|
| Is the hose over about 3 inches OD? | Lean heavy duty | Standard is usually enough |
| Is the joint under pressure spikes or boost? | Heavy duty | Standard |
| Is the hose thick-walled or stiff? | Heavy duty | Standard |
| Is the hose soft silicone with a thin wall? | Check liner and width, heavy duty’s wider band helps | Standard |
| Is a failure expensive or unsafe? | Heavy duty, and consider a spring-loaded T-bolt for large hose | Standard |
| Is tool access tight? | Standard, 5/16 in hex is smaller than 3/8 in | Either |
The 5/16 inch and 3/8 inch hex sizes on OneTouch’s standard and heavy duty clamps are a small thing that matters in the workshop. A fleet that standardises on one family needs only one nut driver, and a mixed fleet should stock both.
Fleet standardisation: fewer part numbers, fewer mistakes
If you maintain many vehicles or machines, the cheapest clamp policy is usually the one with the fewest part numbers that still covers your hoses. Constant tension clamps help here because their range is generous, but the policy still needs a few rules.
- List the hoses. Write down every clamped hose OD on the fleet, with the fitting installed. Ten minutes with calipers on one example of each vehicle type is enough.
- Group by range. Put each hose into the clamp range that holds it mid-range. Many groups will be two or three hoses wide.
- Pick the smallest set. Choose the fewest clamp sizes that cover all the groups, and note any hose that needs a special size.
- Choose one build per group. For example, stainless-screw heavy duty for coolant and charge air, standard for small heater hoses.
- Label the shelf. Part number, band width, screw material and the install method, so a technician at 2 a.m. does not have to guess.
- Review yearly. New vehicles and new hoses change the list.
A policy like this also makes ordering easier, because a distributor can quote a stable list and a stock level, and our bulk buying guide for distributors covers how that conversation goes.
Five datasheet traps
| Trap | What it looks like | Why it matters | What to ask |
|---|---|---|---|
| “Stainless” with no grade | “Stainless steel constant tension clamp” | Could be 201, 430, 301 or 304 | Grade of band, housing, screw and washers |
| Torque shown as pressure | “Rated 90” in a column labelled pressure | Torque is not pressure | The unit and what the number limits |
| Standard and heavy duty blended | One part number for two band widths | Different loading and range | Band width in writing |
| Silent washers | No mention of the spring stack | Washer quality drives life | Material and number of washers |
| Range without the mid-point | Min and max only | Mid-range placement matters | Range for the exact part |
What it costs
Constant tension clamps cost more than plain worm gear clamps, and you should budget accordingly. As a benchmark, one US truck-parts brand lists common sizes at roughly fourteen to twenty dollars each at retail, for example on its small-size and mid-size pages. Prices change, so treat these as a rough order of magnitude and check current listings.
The better question is what the clamp avoids. A weep that returns after every heat cycle costs labour, coolant and sometimes a roadside callout. On a vehicle or machine where downtime is expensive, a clamp that holds its seal through relaxation can pay for itself on the first avoided repeat visit. On an easy, low-consequence joint, a standard clamp checked at service is often enough. Our explanation of why hose clamps loosen over time shows where the avoided cost comes from, and constant tension vs standard hose clamp compares the two across a heat cycle.
Copy-paste RFQ template
Paste this into an email or purchase request and fill in the brackets. It covers the six lines of the card.
- Item: constant tension (constant torque) hose clamp, worm gear type with Belleville washers.
- Hose and fitting: [hose type], measured outside diameter [__] in / mm over the fitting.
- Clamp range required: [__] to [__], hose mid-range.
- Band width and series: [9/16 in standard / 5/8 in heavy duty].
- Band and housing material: [301 / 304 / 316 stainless], grade to be stated in the quote.
- Screw material and drive: [410 stainless / 304 stainless / zinc-plated], hex size [__].
- Washers: material and number of washers to be stated.
- Load rating: maximum torque and installation method to be stated.
- Liner: [required / not required].
- Operating conditions: temperature [__] to [__], fluid [__], environment [dry / wet / salt / chemical].
- Quantity and packing: [__] pieces, boxes of [__].
- Documents: [material certificate / certificate of conformity / none].
- Delivery: [location and date].
OneTouch will answer an RFQ in this format from the quote page, and the clearer the lines, the faster the match.
Incoming inspection: six checks on delivery
When the parts arrive, spend ten minutes before they go on the shelf.
- Count and label. Quantity, part numbers and band width match the order.
- Band and housing. Edges are smooth, no cracks, housing seated and free of sharp burrs.
- Screw. Correct hex size, clean threads and a head that is not already rusty. A magnet gives a clue to screw material: plated carbon steel and 410 stainless are attracted, 300-series is generally not.
- Washer stack. Visible and intact. When the clamp is closed on a mandrel and torqued, the washers should end nearly flat.
- Screw tip projection. After tightening, the screw tip should extend beyond the housing by the amount the maker specifies. Several makers give about a quarter inch.
- Range. Close the clamp on a test diameter at the middle of its range and check that it moves smoothly.
Spot-check a small percentage of a large order, and retain samples from each lot for comparison if a problem appears later. The sibling guide on constant tension hose clamp torque specifications explains the washer and tip checks in more detail, and how to install a constant tension hose clamp covers fitting.
When constant tension is not the right buy
- Very high pressure or very large hose. A T-bolt or spring-loaded T-bolt may suit better; see how to choose a T-bolt hose clamp.
- Tiny hoses. A mini clamp is more appropriate below about three quarters of an inch.
- Rigid pipe joints. The spring has nothing to follow if neither part moves.
- Cut-prone soft hose with no liner. Choose a lined or non-perforated option, as explained in why hose clamps cut into hoses.
- Severely worn hose. No clamp can rescue a hose that has hardened or cracked.
For a complete view of the stainless options, the overview of stainless steel constant tension hose clamps lists the benefits, and the hose clamp glossary defines terms such as Belleville washer and cold flow.
Frequently asked questions
What should I look for when buying a constant tension hose clamp?
Check the size range with your hose mid-range, the band width, the grade of band, housing and screw, the washer details, the torque rating and installation method, and whether a liner is fitted. A datasheet that is silent on any of these deserves a question to the supplier.
What is the load rating of a constant tension clamp?
Usually it is the maximum torque the screw and housing should see, not the pressure the joint will hold. Read it as a ceiling, and install by the maker’s method, which often relies on the washers collapsing nearly flat and a set screw-tip projection.
What is the difference between standard and heavy duty constant tension clamps?
Heavy duty versions use a wider band, often 5/8 inch against 9/16 inch, a larger hex drive and a higher torque rating. On OneTouch’s range the standard series is rated at 70 inch-pounds and the heavy duty series at 92.
Are constant tension clamps all stainless steel?
Not necessarily. Many have a stainless band and housing with a plated or 410 stainless screw. Ask for the material of every part, including the washers, if corrosion resistance matters.
Do constant tension clamps include a liner for silicone hose?
Some do and some do not. A liner is an extended inner band that covers the screw slots. OneTouch’s constant tension product pages do not state one, so ask before ordering for silicone.
How much do constant tension hose clamps cost?
More than plain worm gear clamps. Retail listings for common sizes from one US brand run from roughly fourteen to twenty dollars each, and distributor pricing varies with volume. Weigh the price against the cost of a repeat leak.
Can I replace a competitor’s constant tension clamp with a OneTouch clamp?
Often, after matching size range, band width and rating. The cross-reference tool and the quote page are the quickest routes, and sending a photo with the hose size helps.