A vacuum truck operator radios the shop: “Need two clamps for the 4 inch suction hose.” Two clamps come out on the next truck, and neither one threads onto the hose. One is wound the wrong way, the other is sized for a hose that measures a quarter inch smaller over the helix. A spiral hose clamp size chart would have helped, but only if someone had first written down the right numbers at the hose. This post gives you both: an order card to fill in at the yard, and a chart that shows why “4 inch” is never enough information on its own.
One thing to say up front: OneTouch does not stock spiral clamps. We make and export worm gear, T-bolt, hi-torque, constant torque, lined and V-band clamps. Where a spiral clamp is the right answer, this guide shows you exactly what to ask your hose supplier for. Where a smooth-cuff hose end means a band clamp will do the job, we point you to the clamps we do carry.
The spiral clamp order card (print it, take it to the hose)
Most wrong spiral clamp orders trace back to one missing line of information. The card below has seven lines. Fill in all seven at the hose, not from memory at the desk, and the order almost always comes back right the first time.
| Line | What to record | How to get it | Your entry |
|---|---|---|---|
| 1. Nominal hose ID | The size printed on the hose or invoice (1-1/2, 2, 3, 4, 6 in and so on) | Read the layline printed along the hose, or check the purchase record | ________ |
| 2. Hose brand and series | Maker plus series code, for example a PVC liquid suction series or a rubber vacuum series | Layline print; photograph it | ________ |
| 3. Crest OD over the helix | Outside diameter measured over the raised ridges, in inches to two decimals | Pi tape, string wrap, or caliper pairs (methods below) | ________ |
| 4. Helix hand | RH (clockwise) or LH (counterclockwise) | Look down the hose end and note which way the ridge winds away from you | RH / LH |
| 5. Helix pitch | Distance from one crest to the next | Measure across five crest-to-crest gaps, divide by 5 | ________ |
| 6. Bolt count and style | Single bolt, double bolt, number of clamps per end | Check what is on the hose now, then the hose maker’s guidance | ________ |
| 7. Material | Zinc-plated steel, 304 stainless, 316 stainless | Match the service: water, sewage, food, chemicals, marine air | ________ |
Lines 1 and 2 pick the catalog. Line 3 picks the clamp. Line 4 decides whether it threads on at all.
Key point: A spiral clamp is sold by nominal hose ID, but it has to fit the crest OD. The two numbers move apart from brand to brand, so line 3 is the one you cannot skip.
A quick word on line 4, helix hand
Hold the hose end toward you and follow a ridge as it travels away. If it turns clockwise, the hose is right hand and needs a right-hand (clockwise) clamp. If it turns counterclockwise, you need a left-hand clamp. Dixon’s spiral clamp listings say Pacific Echo and Kanaflex hoses use clockwise clamps, Kuriyama uses counterclockwise, and Goodyear makes both, so you have to check a Goodyear hose before you order. Our guide on how to choose a spiral hose clamp walks through hand matching and fitting selection in full. This post stays with sizing.
Spiral hose clamp size chart by nominal hose ID
The chart below lines up four sets of real maker data for each nominal size. Three columns give the published nominal OD of a hose family. The last column gives the published OD range of one maker’s spiral clamp at that size. The point is not to tell you which clamp to buy. The point is to show how much the crest OD of a “3 inch” hose can vary, and where a given clamp stops fitting.
Sources: standard-duty PVC values come from Kuriyama’s K series standard duty PVC suction hose listing. Heavy-duty PVC values come from the Tigerflex W series heavy duty liquid suction spec table. Rubber-with-PVC-helix values come from the Kanaflex Kanavac AR data sheet. Clamp ranges come from Dixon’s spiral clamp catalog (see the Dixon SC250 clockwise spiral clamp page for one example). Fractions are converted to decimals and rounded.
| Nominal hose ID | Standard-duty PVC helix, nominal OD (Kuriyama K) | Heavy-duty PVC helix, nominal OD (Kuriyama W) | Rubber, PVC helix, nominal OD (Kanavac AR) | Dixon spiral clamp OD range (SC / SCCW) | Clamps per end (typical) |
|---|---|---|---|---|---|
| 1-1/2 in (38 mm) | 1.83 in (46.5 mm) | 1.85 in (47 mm) | 1.9 in (48 mm) | 1.53 to 1.81 in (39 to 46 mm) | 1 |
| 2 in (51 mm) | 2.32 in (59 mm) | 2.40 in (61 mm) | 2.4 in (61 mm) | 2.28 to 2.50 in (58 to 64 mm) | 1 |
| 2-1/2 in (64 mm) | 2.87 in (73 mm) | 2.99 in (76 mm) | 3.0 in (76 mm) | 2.72 to 3.13 in (69 to 79 mm) | 1 |
| 3 in (76 mm) | 3.43 in (87 mm) | 3.64 in (92 mm) | 3.5 in (89 mm) | 3.00 to 3.50 in (76 to 89 mm) | 2 or more |
| 4 in (102 mm) | 4.50 in (114.7 mm) | 4.76 in (121 mm) | 4.63 in (118 mm) | 4.00 to 4.50 in (102 to 114 mm) | 2 or more |
| 5 in (127 mm) | not listed | 5.75 in (146 mm) | 5.76 in (146 mm) | 5.09 to 5.50 in (129 to 140 mm) | 2 or more |
| 6 in (152 mm) | 6.75 in (171.4 mm) | 7.00 in (178 mm) | 6.8 in (173 mm) | 6.25 to 7.00 in (159 to 178 mm) | 2 or more |
| 8 in (203 mm) | 8.86 in (225 mm) | 9.18 in (233 mm) | 9.04 in (230 mm) | 8.50 to 9.25 in (216 to 235 mm) | 2 or more |
| 10 in (254 mm) | not listed | 11.56 in (294 mm) | 11.18 in (284 mm) | 10.63 to 11.25 in (270 to 286 mm) | 2 or more |
| 12 in (305 mm) | not listed | 13.64 in (346 mm) | 13.31 in (338 mm) | 11.81 to 12.95 in (300 to 329 mm) | 2 or more |
What the chart tells you at a glance
- Same nominal size, different OD. At 4 in nominal, the three hose families span 4.50 to 4.76 in over the helix. That is about a quarter inch of spread on one “size”.
- A clamp range can miss a hose of the same nominal size. Dixon’s 4 in spiral clamp is listed for 4.00 to 4.50 in OD. The standard-duty PVC hose sits right at the top of that range; the heavy-duty PVC and rubber hoses sit above it. At 3, 5, 10 and 12 in you see the same pattern with at least one hose family.
- Some sizes fit easily. At 2 in and 6 in, all three hose families land inside the Dixon range. Those are the sizes where a nominal order usually works.
- Small sizes can run the other way. At 1-1/2 in, all three hoses publish an OD above the top of Dixon’s listed range. Dixon’s own page notes that hose OD fluctuates and each installation should be checked, which is the honest answer here.
None of this means one maker’s clamps are wrong. Clamp makers usually design around one or two hose families, often the brand they sell alongside. Hose makers also publish their own matched clamp series. Kuriyama, for example, lists its counterclockwise double-bolt clamps for its Tigerflex PVC suction hose and refers buyers to its accessories compatibility chart. The safest order is the one where clamp and hose come from a matched pair, or where you have checked your measured OD against the clamp’s published range.
Double bolt spiral clamp sizes and how many per end
Most spiral clamps for suction hose are double-bolt designs: a spiral rod formed to the helix, with two bolts pulling a saddle closed. Kuriyama’s SDBC-3 spiral double bolt clamp page lists an 8 ft-lb maximum torque at 3 in and tells users to fit two or more clamps on hoses 3 in ID and larger, with both nuts tightened evenly. The same family lists 24 ft-lb at 4 in and 30 ft-lb at 12 in. Those are maximums, not targets; tighten until the clamp seats in the root and stop.
Line 6 on your card should record two things: the bolt style on the clamp you are replacing, and the count per hose end. If the old fitting had two clamps, order two. If it had one on a 4 in hose, ask why before you copy it.
How to measure suction hose OD over a ridged helix
A smooth hose is easy to measure. Ridged suction hose is not, because there is a crest diameter (over the helix), a root diameter (in the valley between ridges) and the hose is rarely perfectly round. Spiral clamps are listed by crest OD, so that is the number you want. Our general guide to measuring hose clamp size covers smooth hose. The four methods below are specific to helix hose. Use at least two and compare.
Method 1: pi tape over the crests
A diameter tape (often sold as a pi tape) is graduated so that wrapping it around a round object reads diameter directly, with no division. Wrap it square to the hose axis, about 1 to 2 in back from the cut end, where the clamp will actually sit. Let the tape ride on top of the crests. Because the helix is a slope, the tape will want to follow it and skew; hold it flat across three or four crests instead. Read to the nearest hundredth.
Watch out: Do not pull a pi tape hard on soft PVC hose. Tension squeezes the crests and reads low. Snug is enough.
Method 2: string wrap, then divide by π
No pi tape in the truck? Use a strip of paper, a cable tie, or non-stretch cord. Wrap it once around the crests, square to the hose axis. Mark where it overlaps, lay it flat, and measure the length with a steel rule. Divide by 3.1416. That is your crest OD.
Paper strip is better than string because it cannot drop into the root. If the hose is 6 in or larger, a fabric tailor’s tape works well too, but check it against a steel rule first; old cloth tapes stretch.
Method 3: caliper across crests in 90-degree pairs
A large vernier or dial caliper works up to about 6 in on most shop tools. Close the jaws on two opposite crests. Note the reading. Rotate 90 degrees around the hose and measure again. Then move along about half a pitch and repeat both readings. Average the four numbers.
This method shows you out-of-round. If one pair reads 2.36 and the other 2.44, the hose is oval, usually from storage on a reel or from being run over. A spiral clamp will often pull a mildly oval hose round. A hose that is badly crushed needs cutting back.
Method 4: pitch over five crests
Pitch is the distance from one crest to the next along the hose. One gap is too small to measure accurately with a tape, so measure across five. Put the end of a steel rule on the top of one crest, count five gaps along (you will land on the sixth crest), and read the distance. Divide by 5.
Hose data sheets rarely publish pitch, so your measurement may be the only record. It matters because the clamp’s spiral rod is formed to a set pitch. A clamp wound for a tighter pitch will ride up onto the crests instead of sitting in the roots. If your supplier offers two clamps for your OD, pitch is often what decides between them.
Rule of thumb: Measure crest OD with two methods. If they agree within about 0.05 in, record the average. If not, measure again at a new spot before you order.
Three worked examples with real numbers
The measurements in these examples are illustrative, chosen to match the published data in the chart above. The working is what you would do in the yard.
Example 1: 3 in hose on a trash pump, string wrap
The layline reads a heavy-duty PVC liquid suction hose, 3 in. A paper strip wrapped over the crests measures 11.42 in. Dividing by π gives 11.42 ÷ 3.1416 = 3.64 in crest OD. That matches the heavy-duty PVC column exactly.
Check the spiral hose clamp size chart: Dixon’s 3 in spiral clamp lists 3.00 to 3.50 in. A 3.64 in hose is over that range, so a generic 3 in clamp from that catalog may not close. Looking down the hose end, the ridge runs counterclockwise away from the viewer, so this hose needs a left-hand clamp. The hose maker’s own 3 in counterclockwise double-bolt clamp, designed for that hose series, is the safer pick. At 3 in ID, order two per end.
Example 2: 6 in vacuum truck hose, pi tape and pitch
A black rubber vacuum hose with a rigid helix, 6 in nominal. The pi tape reads 6.82 in over the crests, about 1.5 in back from the cut end. A second reading at 3 in back gives 6.79 in. Average: 6.81 in.
Pitch: the rule across five crest gaps reads 4.10 in, so 4.10 ÷ 5 = 0.82 in pitch (illustrative). The helix runs clockwise away from the viewer: right hand. Dixon’s 6 in clamp is listed for 6.25 to 7.00 in, so 6.81 in sits comfortably inside. For a vacuum truck hose clamp size, that is a good result: a right-hand 6 in spiral clamp, two per end, in stainless if the truck works septic or industrial waste. Send the pitch with the order so the supplier can confirm the rod form matches.
Example 3: 2 in transfer hose, caliper pairs
A 2 in clear PVC suction hose that has lived on a reel. Caliper readings: 2.36 and 2.44 in at 90 degrees, then 2.38 and 2.42 in half a pitch along. Average: (2.36 + 2.44 + 2.38 + 2.42) ÷ 4 = 2.40 in. The 0.08 in difference in the first pair shows mild oval from reel storage.
Dixon’s 2 in clamp covers 2.28 to 2.50 in, so 2.40 in fits with room each side. One clamp per end is typical below 3 in ID. Tightened evenly, the clamp should pull the oval back round. If it does not seat in the roots on both sides, cut 2 in off the end and measure again.
When the spiral hose clamp size chart lies
These four situations are where a clamp ordered straight off a chart most often fails to fit.
Brand-specific OD
You have already seen it in the chart: at 4 in nominal, published ODs span 4.50 to 4.76 in across three hose families, and that is only three of dozens on the market. Imported hose with metric IDs adds another layer. Kuriyama, for instance, sells metric WT sizes with IDs of 1.77, 2.24 and 2.36 in and lists separate clamps for them. A “2 in” clamp for a 1.77 in ID metric hose is a guess, not an order. Write the brand and series on line 2 every time.
Cuffed versus uncuffed ends
Some suction and discharge hose comes with smooth, helix-free cuffs at each end, built to take a standard band clamp. Others are cut from bulk, so the helix runs right to the end. A spiral clamp is only for the second case. On a smooth cuff, a spiral rod has nothing to sit in and will not seal.
If you have a smooth cuff, measure the cuff OD like any smooth hose and use a band clamp. A T-bolt clamp spreads load evenly on large hose. A hi-torque worm gear clamp covers wide diameter ranges if you are not sure of the exact cuff size. Our 4 inch hose clamp size range and 6 inch hose clamp size range guides cover the common cuff sizes on pump and truck hose.
Wear on the crests
Hose dragged across concrete or a truck deck loses material off the helix crests first, so it can measure under its published OD and give the clamp rod less to bear on. Measure where the clamp will sit. If the crests are visibly flattened at the end, cut back to sound hose first.
Cold PVC
PVC hose stiffens in the cold. A hose that has sat at 20°F will resist the clamp and may not measure the same once it warms in service. If you can, bring the hose end inside for an hour before measuring and fitting, then recheck clamp seating after the hose has run warm.
Key point: The chart gives you a shortlist. Your measured crest OD, taken at the clamp position, picks the clamp.
Spiral clamp sizes for 2, 3, 4 and 6 inch hose: a quick reference
These four sizes cover most pump, irrigation and vacuum truck work.
- 2 in hose: crest OD typically 2.3 to 2.4 in. One clamp per end. A nominal 2 in clamp usually fits, but confirm hand.
- 3 in hose: crest OD typically 3.4 to 3.65 in. Two clamps per end. Heavier hose can exceed a 3 in clamp’s top range, so measure.
- 4 in hose: crest OD typically 4.5 to 4.8 in. Two clamps per end. The most common size for wrong-fit orders; always send the measured OD.
- 6 in hose: crest OD typically 6.75 to 7.0 in. Two clamps per end. Common on vacuum trucks and dewatering pumps; specify stainless for sewage service.
For metric references and conversions between fractional and decimal sizes, our hose clamp size chart in mm and inches has the full table.
Line 7: picking the material
Spiral clamps are commonly sold in zinc-plated carbon steel, with stainless versions available in some sizes. Kuriyama, for example, offers its 2 and 2-1/2 in counterclockwise double-bolt clamps in 304 stainless as well as plated steel. Plated steel is fine for clean water and dry service. Sewage, slurry, food transfer, fertilizer and anything near salt air push toward stainless. If you are deciding between grades, our post on 304 vs 316 spiral hose clamps covers it.
A filled-in example card
Here is the order card completed for Example 2, the 6 in vacuum truck hose. This is what a supplier needs to quote the right part first time.
| Line | Entry | Notes |
|---|---|---|
| 1. Nominal hose ID | 6 in (152 mm) | From layline |
| 2. Hose brand and series | Rubber vacuum hose with rigid PVC helix; maker and series as printed | Photo of layline attached |
| 3. Crest OD over helix | 6.81 in (173 mm) | Pi tape, average of readings at 1.5 in and 3 in from cut end |
| 4. Helix hand | RH (clockwise) | Viewed from hose end, ridge winds clockwise away |
| 5. Helix pitch | 0.82 in (21 mm) | 4.10 in over five crest gaps ÷ 5 (illustrative) |
| 6. Bolt count and style | Double bolt, 2 clamps per end, 4 clamps total | Two hose ends; matches existing setup |
| 7. Material | Stainless | Septic service; grade per supplier advice |
Send the card with the layline photo. “6 in, RH, 6.81 in crest OD, 0.82 in pitch, double bolt, stainless, qty 4” gets a quote in minutes; “6 in spiral clamp” gets a callback.
If a spiral clamp is not the right clamp
Spiral clamps are one of two common clamps for ribbed suction hose. The other is the double wire clamp, two loops of round wire that cinch over the crests and can be bent to follow the hose. Our guide to stainless steel double wire hose clamps covers where they beat a spiral clamp. If you want the background on how a spiral clamp seals in the helix roots, read what a spiral hose clamp is. For the bigger picture on clamping pump and truck hose, see our roundup of the best hose clamps for suction and discharge hoses.
Sizing a different clamp type with the same card-first approach? Our sibling post, the spring band hose clamp size chart, does the same job for spring clamps on small coolant and vacuum lines.
Spiral hose clamp size chart FAQ
Are spiral clamps sized by hose ID or hose OD?
Both, in a way. They are named by nominal hose ID (a “4 in” clamp is for 4 in ID hose), but each one only closes properly over a set range of crest OD. Makers such as Dixon publish that OD range. Order by ID, confirm by OD.
How do I measure suction hose OD with no special tools?
Wrap a strip of paper once around the crests, square to the hose, and mark the overlap. Measure the strip with a steel rule and divide by 3.1416. Paper works better than string because it bridges the valleys instead of sinking into them.
What is the difference between left hand and right hand spiral clamps?
They are wound in opposite directions to match the hose helix. Look down the hose end: if the ridge turns clockwise away from you, use a right-hand clamp; counterclockwise, use left hand. A wrong-hand clamp will not thread on at all. The full method is in our spiral clamp selection guide.
How many spiral clamps do I need per hose end?
One is common below 3 in ID. Kuriyama’s guidance for its double-bolt spiral clamps is two or more on hoses 3 in ID and larger. Dixon also notes that more than one clamp may be needed and suggests checking with the hose maker. For vacuum truck and pump hose under load, two per end is the usual practice.
What size spiral clamp fits a 4 inch vacuum truck hose?
A 4 in nominal clamp of the correct hand, but check the range. Published crest ODs for 4 in hose run roughly 4.50 to 4.76 in, and some 4 in clamps are listed only up to 4.50 in. Measure the crest OD at the clamp position and send it with the order.
Why does my measured OD not match the hose data sheet?
Data sheets give a nominal value. Lot-to-lot variation, crest wear, out-of-round from reel storage, cold stiffening and tape tension all shift the reading. If your figure is within a few hundredths, use it. If it is far off, measure at a fresh spot and check you have the right series.
Can I use a band clamp instead of a spiral clamp on ribbed hose?
Not on the ribbed section; a flat band bridges the valleys and leaks. A band clamp is correct on a smooth cuff molded onto the hose end. For bare helix hose, use a spiral clamp or a double wire clamp.
Does OneTouch sell spiral hose clamps?
No. OneTouch makes worm gear, hi-torque, T-bolt, constant torque, lined and V-band clamps. For smooth-cuff hose ends we can supply a matching band clamp, and our cross-reference tool helps match part numbers from other makers.
Next step: fill in the card, then match the clamp
Print the order card, take it to the hose, and fill in all seven lines. Check your crest OD against the spiral hose clamp size chart above, then order spiral clamps from the hose maker or a matched supplier. If your hose has smooth cuffs instead of a bare helix, OneTouch can help: pick a T-bolt or hi-torque clamp by measured cuff OD, use the hose clamp cross-reference tool to match an existing part number, or send your measurements through our quote request page for bulk pricing.