Knowledge

German Type Hose Clamp Buying Guide: Material, Size and Load Rating

Pick up any German type hose clamp and turn it over. Somewhere on the band, usually stamped or etched in tiny letters, is most of what a buyer needs to know: a size range, a band width, a material code and sometimes a brand mark. Most purchasing mistakes with this clamp family come from not reading that stamp, or from ordering without knowing what the characters mean.

This guide is built around that stamp. We decode it piece by piece, and for each piece we explain the buying decision behind it: the band width, the W-code that signals the material, the size range, and the torque and pressure figures that stand in for a “load rating”. We finish with inspection steps, a request-for-quotation template and a set of supplier questions. For the definition, read what is a German type hose clamp; for the standard behind it, see DIN 3017 hose clamp standard explained; and for a shorter selection summary, how to choose a German type hose clamp.

What we supply. OneTouch Exim does not supply German type clamps; they are not in our catalogue. Our closest equivalents are lined worm gear clamps and perforated worm gear clamps. We have written this guide because buyers regularly ask how to specify German type clamps from other suppliers, and because it helps you judge when one of our smooth-lined clamps is a reasonable substitute.

In this guide

First, what does “German type” actually promise?

“German type” is a trade label, not a certification. It describes a design: a steel strap with a thread profile pressed into it rather than cut through it, so the inside face of the band stays closed. That smooth underside is gentler on soft hose than the slots of a perforated band. The name refers to the shape of the product, not to where it was made, and a listing can borrow the look without meeting the standard.

The standard is DIN 3017. Parts made to it have defined band widths, material codes, clamping ranges and tightening torques. If you need the standard, say so in writing and ask the supplier to confirm conformity in writing; do not rely on the name alone. For how this style compares with the American slotted type, see German type vs American type hose clamp.

Reading the stamp, part one: the band width

The two standard band widths are 9 mm and 12 mm. Mini versions use narrower bands, and heavy-duty versions use wider, thicker ones. Some maker ranges also include 7.5 mm and 16 mm bands, which fit the same families but are outside the two core widths.

Band widthTypical thicknessWhere it fits
9 mmabout 0.6 mmSmall to medium hose, general purpose
12 mmabout 0.7 to 0.8 mmLarger diameters and higher load
Narrower (such as 5 or 7.5 mm)ThinVery small hose, tight spaces
Wider (such as 16 mm)ThickerHeavy duty, large hose

Thicknesses vary by maker. One embossed-band supplier lists 0.6 mm for its 9 mm band and 0.7 mm for its 12 mm band (Evereon listing), while a distributor catalogue lists 0.8 mm for its 12 mm clamps (Tubes International catalogue card).

Buying rule. A wider band spreads the load over more of the hose, which helps on soft hose and larger diameters. It also needs a stronger screw and more torque to close. Do not simply pick the widest band: match it to the hose, as explained in hose clamp band width. As a rough guide, 9 mm is the default for small hose, and the 12 mm band takes over as diameters grow.

Reading the stamp, part two: the W-code and the material

DIN 3017 clamps carry a W code that tells you the material combination. The codes run from W1 to W5, and the general pattern is easy to remember.

CodeGeneral meaningTypical use
W1Zinc-plated steel throughoutDry, indoor, low-cost
W2Stainless band and housing, plated steel screwModerate moisture, cost-conscious
W3Stainless (typically ferritic) throughoutGeneral wet use, better corrosion resistance than W2
W4Austenitic stainless (304-type) throughoutOutdoor, food, chemical and marine-adjacent use
W5Higher-grade austenitic (316-type) throughoutHarsh, coastal and chemical environments

Treat this table as a map and not as a specification. Exact grades for each code can differ between makers and revisions of the standard, so check the supplier’s datasheet for the actual alloy of the band, housing and screw. Our dedicated explainer, hose clamp W1, W2, W4, W5 meaning, goes through the codes in more depth.

The material questions that matter

  • Is the screw the same material as the band? W2 clamps deliberately use a plated screw, which is the part most likely to rust.
  • Is the housing the same material? The housing carries the thread engagement. A weak housing fails under torque.
  • Is it magnetic? Ferritic stainless (W2/W3 band) is magnetic, and austenitic is largely non-magnetic. A magnet is a hint, not proof; read magnetic vs non-magnetic stainless steel.

For environment-specific advice, see 304 vs 316 German type hose clamps, stainless vs galvanized German type hose clamps and stainless steel German type hose clamps. Where salt is involved, hose clamp corrosion in coastal areas explains why a few extra pence per clamp is a bargain.

Reading the stamp, part three: the size range

German type clamps are multi-range. Each part number covers a span of diameters, and the ranges are standard steps rather than arbitrary values. NORMA’s TORRO 9 mm range, for example, lists steps such as 8 to 12, 10 to 16, 12 to 18, 12 to 22, 16 to 27, 20 to 32, 25 to 40, 30 to 45, 35 to 50 and 40 to 60 mm (NORMA TORRO catalogue), and the full DIN 3017 series runs from small hose up to 140 to 160 mm and beyond.

How to pick the right range

  1. Measure the outside diameter of the hose where it sits on the fitting. The clamp goes over the hose on the barb, so the hose OD on the fitting is the size that matters. See how to measure hose clamp size.
  2. Find ranges that include the measurement. Neighbouring ranges overlap, so more than one may qualify.
  3. Choose the range that puts your hose near the middle. A clamp used at the extreme of its range has less adjustment left and sits less evenly.
  4. Check that the clamp is not wildly oversize. An oversize band leaves a long loose tail and a screw housing that sits on the hose unevenly.

Use the German type hose clamp size chart and the hose clamp size chart in mm and inches for a first-pass match.

A worked example (illustrative)

Your hose measures 25.5 mm on the fitting. Two candidate ranges are 20 to 32 mm and 25 to 40 mm. The 25 to 40 mm clamp has your hose at the very bottom of its range, so it sits almost fully open and may be too loose to tighten correctly. The 20 to 32 mm clamp has your hose about a third of the way up the range, which is comfortable. Choose the 20 to 32 mm clamp. These ranges follow typical catalogue steps, but always confirm against the actual product drawing.

Reading the stamp, part four: what “load rating” really means

German type clamp datasheets do not use one number called load rating. They give a set of torque figures and sometimes a pressure value, and each one answers a different question. NORMA’s catalogue names the four torque values that matter: recommended tightening torque, no-load (free-running) torque, test torque and breaking torque.

TermMeaningWhy a buyer cares
Recommended tightening torqueThe torque to apply during installationThe number for your installation procedure
Free-running (no-load) torqueThe torque needed to turn the screw before the clamp loads the hoseShows how smooth the thread is; a high value means a rough or poorly made thread
Test torqueThe torque the clamp must withstand in a test without damageA quality margin above the installation value
Breaking torqueThe torque at which the clamp failsThe upper limit; never approach it

Published examples

Published figures show how installation torque varies by band width and range. These are examples from different makers, not recommendations for your clamp.

SourceBand and rangeTightening torqueUpper figure
Oetiker worm drive clamps9 mm band, 8 to 20 mm2 ± 0.5 N·mTest torque max 2.6 N·m
Oetiker worm drive clamps9 mm band, 12 to 160 mm3 ± 0.5 N·mTest torque max 4 N·m
Oetiker worm drive clamps12 mm band, 16 to 160 mm5 ± 0.5 N·mTest torque max 6.5 N·m
Aspen Fasteners DIN 3017 type A9 mm band, 8 to 110 mm and up3.0 N·mBreaking torque 4.0 N·m
Evereon embossed clamps9 mm / 12 mm4.0 N·m / 5.0 N·m (35 / 44 in·lb)Not stated
Würth DIN 3017 clamp9 mm band, 60 to 80 mm3 N·mNot stated

The Oetiker rows follow our reading of its table, which groups the figures by band width and range, so check the original before relying on them. Sources: Oetiker worm drive clamp data, Aspen Fasteners DIN 3017 data, Evereon listing and Würth product page.

Two lessons follow. First, the gap between the installation torque and the breaking torque is narrow, about one third more in the Aspen example, so a buyer should write the installation torque into the procedure and discourage “a bit extra”. Second, makers differ, so the torque on the datasheet of the part you buy is the figure that counts. For a deeper discussion, see hose clamp torque chart and how tight should a hose clamp be.

Pressure ratings are not what they seem

When a datasheet gives a maximum medium pressure, read the footnote. In one distributor catalogue, a 9 mm clamp for 12 to 22 mm hose is listed at 45 bar, but the same family for 130 to 150 mm hose is listed at only 6 bar, and a 12 mm clamp for 220 to 240 mm hose at 1.6 bar. The catalogue notes that the values depend on hose type and connection shape (Tubes International catalogue card). Pressure capability falls sharply as diameter grows, because the same pressure creates a far larger separating force on a large hose. A marine product listing shows a similar pattern for a small 9 mm clamp with 45 bar (Vetus HCS12).

The practical rule is simple. A pressure figure is valid only for the hose, fitting and size that it was tested on. If the application sees real pressure, test the joint, and consider a stronger clamp style. See hose clamps for high-pressure applications.

Build details that separate a good clamp from a poor one

  • Housing design. Asymmetric housings are designed so the housing does not tilt away from the hose during tightening, and the load is spread more evenly. Würth and NORMA both describe this feature on their DIN 3017 ranges.
  • Rolled edges. Smooth, rounded band edges protect the hose. Sharp edges cut it.
  • Embossed, closed underside. The pressed thread leaves the inside of the band smooth, which is the reason to choose this clamp family on soft hose.
  • Screw head. A 7 mm hex head with a slot fits a socket or screwdriver. A hex head makes consistent torque easier.
  • Thread quality. The screw should turn freely and engage the band evenly. A rough thread wastes torque and can strip.
  • Band thread profile. The pressed thread should be clean and uniform, with no burrs.

Inspect before you accept the order

  1. Check the stamp. Confirm the size range, band width and material code against your order. A missing or unreadable stamp is a red flag.
  2. Look at the underside. It should be smooth and closed, with no slots.
  3. Feel the edges. No burrs, and rounded corners.
  4. Turn the screw. It should run freely along the full band, with consistent resistance.
  5. Tighten a sample. Close the clamp on a gauge ring or scrap hose to the recommended torque and look for even contact, no tilting and no tearing of the band.
  6. Do a magnet check. Compare band, housing and screw against the material code, as a screening step. Ask for a certificate if grade matters.
  7. Retain a sample. Keep a few clamps from each batch for comparison if a problem appears later.

For further quality routines, see how hose clamps are tested for quality and the hose clamp buying checklist for purchase managers.

Buying mistakes we see most often

  • Treating “German type” as a guarantee. Without a stated DIN 3017 conformity, the name is only a description of the look.
  • Ordering by nominal hose size. Clamp ranges are in millimetres of outside diameter on the fitting. A hose called “25 mm” may measure 27 or 28 mm once it is on the barb.
  • Using the extreme of a range. A clamp at the very bottom or top of its span has little adjustment left.
  • Buying W1 for a wet joint. Plated steel is cheap, but a damp engine bay, a wash-down area or a garden shed will take it apart within a season or two.
  • Forgetting the screw. A stainless band with a plated screw behaves like plated steel at the screw. Ask which parts are stainless.
  • Ignoring torque. A 9 mm clamp has little margin between installation and breaking torque. Specify the figure and train the installer.
  • Using a perforated clamp on silicone hose because it was cheaper. A slotted band can print into soft hose. A closed band or a lined clamp is the safer choice.
  • Mixing metric and inch references. If your equipment is specified in inches, convert carefully, and use the size chart in mm and inches to confirm.

Storage and handling

Clamps are small and rarely get the same care as other stock, but a few habits protect them. Keep W1 and W2 parts dry, because zinc plating and plated screws are the first to show rust. Keep sizes separated and labelled with the stamped range, not only the nominal size. Store clamps with the screw backed out far enough that the band can be opened to its full diameter, so the thread is not under strain. Use older stock first. And keep stainless clamps away from carbon steel swarf and grinding dust, since embedded iron particles can cause rust marks on stainless surfaces.

Questions to put to a supplier

  • Do these clamps conform to DIN 3017, and can you confirm it in writing?
  • What is the W-code and the exact alloy of the band, housing and screw?
  • What are the recommended tightening torque, test torque and breaking torque for each size?
  • What are the band width and thickness?
  • Do you quote a pressure figure, and on what hose and fitting was it measured?
  • Is the housing symmetric or asymmetric?
  • Can you provide a material certificate and a batch or lot number?
  • Can you supply a sample before a full order?

Request-for-quotation template

  • Clamp type: German type (embossed band), DIN 3017 type A, conformity declaration required.
  • Band width: [9 mm / 12 mm], thickness: [mm].
  • Range: [mm to mm] and hose OD [mm].
  • Material code: [W1 / W2 / W3 / W4 / W5], with grade for band, housing and screw.
  • Screw head: [7 mm hex, slotted or cross-slot].
  • Torques: recommended tightening, test and breaking, in N·m.
  • Pressure figure (if any) with test conditions.
  • Documents: material certificate, drawing, [RoHS / REACH] statement.
  • Packaging: [pieces per box], labelled with size and batch.

Three buyer profiles

The OEM or appliance maker

Your priorities are conformity, traceability and repeatable torque. Specify DIN 3017 in the drawing, fix the W-code and torque, and require a first-article inspection. Audit batches by torque test and dimensions.

The workshop or repair shop

You want a few kits that cover most jobs. A mixed kit in W1 is cheap but short-lived on wet joints, so stock W4 stainless for coolant, marine and outdoor work. Make sure the kit sizes match the hoses you see.

The distributor

You need a range that sells without hundreds of part numbers. Cover the main DIN ranges in two materials, label the stamp information clearly on the packaging, and hold a few 12 mm sizes for larger hose. Be honest on the product page about conformity: a “German type” listing that does not claim DIN 3017 should not be sold as if it does. For stocking, see bulk hose clamp buying guide for distributors.

When a German type clamp is not the best purchase

If you are not sure, send a photo, a measurement or a part number to get a quote, and we will suggest the nearest suitable option from what we export.

Frequently asked questions

What does German type mean on a hose clamp?

It describes a screw-tightened band clamp with a pressed thread and a closed, smooth inner surface, normally made to DIN 3017. It is a design label, not a place of origin or a certificate.

What band width should I choose, 9 mm or 12 mm?

Use 9 mm for small to medium hose and 12 mm where diameters or loads are higher. The wider band spreads load better but needs a stronger screw and more torque.

What do W1 to W5 mean?

They indicate the material combination, from plated steel at W1 through stainless variants at W2 and W3 to austenitic stainless at W4 and a higher grade at W5. Check the supplier datasheet for the exact alloys.

What is the load rating of a German type clamp?

There is no single figure. Use the recommended tightening torque, test torque and breaking torque, and treat any pressure rating as valid only for the hose and fitting on which it was measured.

How tight should I fasten a 9 mm German type clamp?

Published examples range from about 2 to 4 N·m, depending on range and maker. Use the figure on your clamp’s datasheet, and see how to install a German type hose clamp.

Further reading

For general background, see the Wikipedia hose clamp article. Related OneTouch Exim guides: types of hose clamps, perforated vs solid band hose clamps and hose clamp screw types.

Related Posts