To install a double ear clamp, slide the correctly sized clamp onto the hose first, push the hose fully onto the barb, then set the band over the barb’s sealing zone, just behind the outermost ridge and clear of the fitting shoulder. Close one ear fully with ear clamp pincers, then close the second. Inspect both ears, leak test the joint and record the result.
That is the whole job in one breath. The double ear clamps that leak in service are usually the ones where someone skipped a step that looked obvious: nobody checked the size against the hose over the barb, the ears ended up facing a fan belt, or a half-closed ear got a second squeeze “to make sure”. Shop floors prevent this with a work instruction sheet. It has numbered operations, lists tools and PPE up front, defines the quality characteristics before anyone picks up a pincer, and ends with a sign-off.
This guide is laid out as that sheet. Print it and adapt the tables for a production cell, a fleet workshop or a farm machinery bay. If you are still deciding whether a two-ear pinch clamp suits your hose, read our guide on how to choose a double ear clamp first. For the crimp technique itself (pincer types, measuring a closed ear and spotting a bad crimp), see our sibling post on how to crimp an ear clamp.
A note before we start: OneTouch Exim does not stock ear clamps of any type. We make and export worm gear, lined, constant torque, T-bolt and V-band clamps. This is an honest how-to for a part you may have bought elsewhere. The later sections show where one of our screw clamps does the job better.
Work Instruction Header: How to Install a Double Ear Clamp
The header tells the operator what the job is, what goes on the bench and what the inspector will check. Fill in the bracketed fields for your own part numbers.
| Header field | Entry for a double ear clamp joint |
|---|---|
| Operation | Secure push-on hose to barbed fitting with a two-ear pinch clamp (permanent, single-use) |
| Part | Double ear clamp, [maker / part number], [material: zinc-plated steel or stainless], [band width] |
| Tools | Ear clamp pincers (front jaw; side jaw for tight access), hose cutter or sharp knife, vernier caliper, paint marker, side cutters for rework |
| PPE | Safety glasses (cut bands spring), cut-resistant gloves for handling cut band ends, hearing protection if the leak test uses compressed air |
| Inputs | Hose [ID x OD, material]; barbed fitting [barb size, number of ridges]; clamp size code [stated open/closed range] |
| Quality characteristics | Correct clamp size for hose OD over barb; hose seated to depth mark; band over sealing zone; both ears closed with no cracking; ears placed for access and clearance; no leak at test pressure |
| Reference documents | Clamp maker’s data sheet and closing instructions; hose maker’s data sheet; this sheet |
The clamp maker’s closing instructions outrank this sheet. Ear clamp designs differ, and some makers specify a closing force, a particular pincer or a closing order. When they do, follow them. The quality characteristics are deliberately set out before work starts, because an inspector who knows what to look for makes faster and more consistent calls.
Operation 10 – Verify the Double Ear Clamp Size Against the Hose
A double ear clamp has no screw to take up slack. All the adjustment comes from deforming two ears, so this operation settles most faults before a tool ever touches the clamp.
Open diameter vs closed diameter: reading the size code
Two-ear clamps are sold by diameter range, for example 0.79–0.91 in (20–23 mm). The larger figure is roughly the open diameter, the band’s inside diameter as supplied with both ears standing. The smaller figure is the closed diameter, what the band would shrink to with both ears fully closed and nothing inside. Each ear holds a short loop of band, and closing it takes that loop out of the circumference.
Size the clamp to the outside diameter of the hose where it sits over the barb, not to its nominal size. The barb stretches the hose. General practice is to put that stretched OD in the upper-middle of the clamp’s range, so that closing the ears compresses the hose and doesn’t just collapse the band onto it. The Wikipedia entry on hose clamps says the same: ear clamps are sized so the ears end up nearly fully closed.
Worked size check (illustrative numbers)
These figures are illustrative, not from any maker’s catalogue. Hose: 1/2 in (12.7 mm) ID reinforced PVC air hose, measured at 0.75 in (19.0 mm) OD off the reel. Push a scrap of the same hose onto a spare barb of the same size, then caliper it across the sealing zone: 0.85 in (21.5 mm). Size the clamp to that target.
| Candidate clamp (illustrative range) | Open dia. | Closed dia. | 21.5 mm target sits… | Verdict |
|---|---|---|---|---|
| A: 17.0–20.0 mm | 20.0 mm | 17.0 mm | Above the open diameter | Reject: will not pass over the seated hose |
| B: 19.8–23.0 mm | 23.0 mm | 19.8 mm | Upper-middle of range | Accept: ears do real work and close well |
| C: 22.5–26.0 mm | 26.0 mm | 22.5 mm | Below the closed diameter | Reject: ears bottom out before the hose is gripped |
Candidate C is the trap. It slides on easily, but even with both ears fully closed the band is not tight on the hose. The joint may pass on the bench and weep in service. Candidate A fails for another reason: in Operation 30 the clamp goes onto unstretched hose, and in Operation 40 it has to slide back over the stretched section on the barb.
Band width, material and damage check
- Band width: check that the sealing zone on the fitting is at least as long as the band is wide. If it is shorter, the band will overhang a ridge or the shoulder.
- Material: zinc-plated steel suits dry indoor work. Stainless suits washdown, outdoor and wet duty. Use what the drawing calls for, and don’t fit plated steel in place of stainless just because it is on the shelf.
- Damage: reject any clamp with a kinked band, a part-closed ear, burrs on the inner edge or a cracked ear root. A loose clamp from a drawer may have been crimped before, so don’t use it.
- Identification: if the bag label is lost, measure the open diameter and keep the clamp out of production until it is identified.
Why this operation matters: good technique later cannot fix a wrong size.
Operation 20 – Prepare the Hose End and Barbed Fitting
- Cut the hose square with a hose cutter or a blade in a guide. Why: an angled or chewed end leaves a channel past the first ridge and seats unevenly.
- Clean the barb and hose bore. Remove swarf, tape fragments and old hose residue. Why: no amount of clamp force will close a leak path made by debris under the hose.
- Inspect the barb for nicks across the ridges, flash or cracks. Why: a scratch running along the barb gives fluid a ready-made path out.
- Mark the insertion depth. Measure from the barb tip to the fitting shoulder and mark that distance on the hose with a paint pen. Why: the mark proves full insertion and shows the inspector where the sealing zone is.
- Lubricate only if needed, and only with a compatible product. Plain water or a mild soap solution is usually enough. Why: petroleum oils can swell or soften some hose compounds, and too much lube lets the hose creep off later.
Lubrication is the step people improvise. Unless the hose data sheet allows them, keep motor oil, penetrating sprays and petroleum jelly away from the hose. EngineerFix’s guide on getting a hose onto a barb fitting gives the same warning. On potable water, food or medical lines, use only what the hose maker and your hygiene rules permit, which is often just clean water. A stiff hose end can be softened in hot water. Never use a flame, and never heat a hose that has carried fuel.
Operation 30 – Pre-Position the Clamp and Plan Ear Orientation
A double ear clamp is a closed ring. It cannot be wrapped around a hose that is already on the fitting, so it goes on first. Forget this and you find out when the hose is already seated.
- Slide the clamp onto the hose and park it past the depth mark. Why: the hose end has to be free to push on.
- Check direction if the maker marks one, for example an inner tongue that should face a set way. Why: a reversed band can leave a step against the hose.
- Dry-fit and decide where the ears will point. Why: rotating a hose that is seated on a ridged barb is hard and can scuff the bore.
Ear orientation rules for a two-ear band
On most double ear clamps the two ears sit roughly opposite each other. If one faces you, the other faces away, possibly into a bulkhead. Plan for both.
- Rotate the clamp so you can reach both ears, for example at 3 and 9 o’clock when working from the front.
- Keep the ears away from belts, pulleys, fan blades, shafts, neighbouring hoses and wiring. A closed ear stands proud of the band and chafes under vibration.
- Point the ears away from places where hands pass, such as sprayer booms and hitches. Closed ears have sharp edges.
- If a joint takes two clamps, stagger the second clamp’s ears relative to the first. If side access is all you have, plan on side-jaw pincers.
Whether you need one clamp or two is covered in our sibling post on how many hose clamps to use on one hose.
Operation 40 – Seat the Hose and Place the Band on the Sealing Zone
- Push the hose straight on, twisting slightly, until the depth mark meets the shoulder. Support plastic fittings so they don’t take a side load. Why: if the hose stops short, part of the sealing zone is left bare.
- Check the mark all the way round. Why: if the gap is uneven, the hose went on crooked.
- Slide the clamp back and set it over the sealing zone. Why: the band has to press hose onto barb, not onto unsupported hose.
- Confirm ear orientation against your plan. Why: this is your last chance to rotate the clamp at no cost.
Where exactly the band should sit
The band belongs on hose lying over the barb body, just behind the outermost ridge on the shoulder side and a few millimetres back from the shoulder. If you made the depth mark carefully, the band ends up just on the barb side of it.
- Not on the hose end lip: a band on the last few millimetres of hose cuts into the cut edge.
- Not past the barb: on unsupported hose the band only collapses the hose and does nothing for the seal.
- Not straddling a ridge: a band on top of a ridge tilts, loads unevenly and its edge can bite the hose.
Operation 50 – Close Both Ears of the Double Ear Clamp
This is the operation that gives the joint its holding force. Closing an ear folds the loop of band flat and pulls the circumference in. You cannot undo it, so when you install a double ear clamp, the order of the steps matters.
- Read the clamp maker’s closing instruction if one is supplied: tool, closing force, order. Why: where it exists, it overrides this sheet.
- Set the pincer jaws square over the first ear, gripping the ear’s base where it meets the band rather than its tip. Why: gripping the tip folds the ear unevenly and can crack it.
- Close the first ear fully in one steady squeeze, without rocking the tool. Why: a single controlled stroke gives an even, repeatable fold.
- Close the second ear fully the same way. Why: the second ear takes up the rest of the band’s slack.
- Check the first ear again. Closing the second ear can pull on the band and partly open the first. If the maker’s instruction covers this, follow it. If there is no maker’s instruction and the first ear has opened, reject the clamp and go to the rework rules. Why: this sheet exists to stop operators re-squeezing an ear that has already been folded.
Use a front-jaw pincer when you can reach the ear head-on and a side-jaw pincer when you can’t, and keep the tool square to the band. Our guide to crimping ear clamps with the right pincers covers tool choice in depth. Tool makers publish data worth reading. Oetiker’s data sheet for its single-action pincers lists front, side and extra-reach jaws and warns that hand tools can exceed a clamp’s maximum closing force.
Shop-floor tip: write “ONE squeeze per ear” on the station board. Most ear clamp rework starts when an operator feels the first ear give and goes back for a second squeeze, which can crack the ear root or over-compress a soft hose.
How to verify closure on a two-ear clamp
An ear clamp has no torque value to check, so verification is visual and dimensional. Each ear should be folded flat and symmetrical, with its legs touching or within the closed-gap value in the maker’s data. The band should be tight enough that you can’t rotate it on the hose by hand. If both ears close completely and the band is still loose, the clamp is too large. That is a sizing failure from Operation 10, not a tooling problem. Post 113 explains how to gauge the closed-ear gap.
Operation 60 – Inspect, Leak Test and Record the Joint
Inspection is an operation in its own right. On a line, the next station does it. In a workshop, put the pincers down first and then work through the list.
| # | Quality point | Method | Accept | Reject |
|---|---|---|---|---|
| 1 | Hose insertion | Visual: depth mark | Mark at shoulder all round | Gap or uneven mark |
| 2 | Band position | Visual / feel | Over barb body, clear of shoulder and ridges | On hose lip, past barb or on a ridge |
| 3 | Ear 1 closure | Visual; gauge per maker | Folded flat, legs meet, symmetrical | Open gap, twisted fold, crack at root |
| 4 | Ear 2 closure | Visual; gauge per maker | As ear 1 | As ear 1 |
| 5 | Band tightness | Try to rotate by hand | No rotation | Band turns on hose |
| 6 | Hose condition | Visual | No cut, bulge or crease at band edges | Band edge cutting hose |
| 7 | Ear orientation | Visual vs plan | Clear of moving parts, hoses, wiring | Ear touching or near a moving part |
| 8 | Leak test | See below | No bubbles, drips or pressure drop | Any leak at the joint |
Leak and pressure test options
These are general practices. Your system’s own test procedure takes priority.
- Air lines: bring the line to working pressure, brush soap solution over the joint and watch for bubbles. Never exceed the hose or fitting rating.
- Water and coolant: check at working temperature, then again after cool-down. Thermal cycling exposes marginal joints.
- Vacuum: watch a gauge for decay. A joint can hold pressure and still draw air under vacuum.
- Fuel: follow the equipment maker’s procedure, with no ignition sources and good ventilation.
Sign-off line template
| Field | Entry |
|---|---|
| Assembly / machine ID | __________ |
| Joint location | __________ (e.g. “compressor outlet, hose 2, fitting end”) |
| Clamp part no. and lot | __________ |
| Pincer ID / check due | __________ |
| Checklist points 1–7 | Pass / Fail |
| Leak test: medium, pressure, hold time | __________ / Pass / Fail |
| Installed by / date | __________ |
| Inspected by / date | __________ |
Logging the clamp lot and pincer ID can look excessive. On 40 sprayers or 500 compressor assemblies, though, it is the only way to trace a weak batch or a worn tool back to the joints it touched.
Rework Rules for a Rejected Ear Clamp
- Never re-crimp a closed ear. The fold is already plastically deformed. A second squeeze stresses the root and the result is unknown.
- Never open an ear to reuse the clamp. Ear clamps are single-use.
- Cut it off. Wear safety glasses and cut through a closed ear with side cutters, keeping the jaws off the hose. Peel the band away slowly, because the cut ends are sharp. EngineerFix’s guide on removing pinch clamps safely describes the same method.
- Inspect the hose. If it is scored, or the end has been on and off the barb more than once, cut it back square and restart at Operation 20.
- Fit a new clamp, repeat Operations 30–60 and mark the sign-off line “rework”.
- Fix the cause. If the ears bottomed out, correct the size code on the sheet. If the folds were uneven, pull the pincer for checking.
Where Double Ear Clamps Are Installed, and When a Screw Clamp Fits Better
Two-ear pinch clamps suit joints that are made once and left alone, and that need a low profile and resistance to tampering. NORMA describes its double-ear clip as a screwless, permanent clamp for low- and medium-pressure air and fluid hoses.
| Application | Why double ear clamps are used | Installation watch-point | Screw clamp alternative |
|---|---|---|---|
| Compressed air lines (tools, small compressors, pneumatic panels) | Compact, tamper-resistant, fast on a line | Soap test at working pressure | Mini or standard worm clamp for field-serviced lines |
| Fuel and vacuum lines (small engines, OEM lines) | Even grip on small, thin-wall hoses | Ears clear of hot or moving parts | Lined worm clamp where the hose is serviced often |
| Water lines (appliances, drinking water kits) | Low profile, no screw to loosen | Compatible lubricant only; recheck after cool-down | Mini or lined worm clamp for repairs |
| Agricultural sprayer lines (booms, tank fittings) | Many identical joints, low snag profile | Ears away from hand paths; chemical-resistant material | All-stainless worm clamp where lines are swapped seasonally |
Signs the joint really wants a screw clamp
An ear clamp is a poor choice if the joint is opened often, if nobody on site owns pincers, or if the stretched hose OD falls between two ear clamp sizes. In those cases an adjustable worm gear clamp is the better choice. OneTouch can supply those, but remember that we don’t sell ear clamps.
- Small hoses (fuel, vacuum, airline): the 0.22–0.63 in mini all-stainless clamp (4SS0004) and the 0.44–0.78 in mini hose clamp (4SC006M) cover the sizes where two-ear clamps are most common, and both can be reused.
- Soft or thin-wall hoses: a lined clamp puts a smooth band between the worm slots and the hose. The 1.06–2.00 in lined worm clamp (4SCH024) is one example. See the lined hose clamp range for other sizes, and confirm the liner material with us for aggressive media.
- General purpose joints: the perforated worm gear clamp range runs from 0.44 in to 7.00 in, with a 301 stainless band and a choice of zinc-plated or all-stainless screw.
For advice on specific applications, see our guides to the best hose clamps for air compressor lines and clamps for garden hoses and irrigation. If your drawing gives a competitor’s part number, our clamp cross-reference lookup maps more than 3,000 OEM and competitor numbers to OneTouch equivalents where one exists. Another permanent-style clamp turns up on low-pressure hose too, and our sibling post covers installing a double wire hose clamp.
Replacing ear clamps across a fleet or a product line? Send us sizes and quantities for a quote. Include the hose OD over the barb so we can suggest the right range.
Double Ear Clamp Installation Questions Technicians Ask
Can I install a double ear clamp with ordinary pliers?
In an emergency, end-cutting pliers can close an ear, but it isn’t good practice. Ordinary pliers grip the tip, fold the ear unevenly and can nick it. Purpose-made ear clamp pincers close the ear from its base in a square, repeatable stroke. For any joint that will be inspected, signed off or put under pressure, use proper pincers and follow the tool recommendation from the clamp maker.
Which ear do I close first on a two-ear clamp?
Unless the clamp maker specifies an order, start with whichever ear is easier to reach. Close it fully in a single squeeze, then close the second ear fully. Afterwards, check that the first ear has not opened. If it has, and the maker gives no instruction for that case, cut the clamp off and fit a new one. Don’t squeeze the first ear again.
What if both ears close completely and the clamp is still loose?
Then the clamp is too large. Its closed diameter is bigger than the hose OD over the barb, so it runs out of take-up before it grips. Cut it off and measure the hose over the barb again. Choose a size that puts that measurement in the upper-middle of the clamp’s range. Don’t add a second loose clamp next to it to compensate.
Can a double ear clamp be reused after removal?
No. Closing an ear deforms it permanently, and you normally remove the clamp by cutting through an ear. Even a clamp that comes off in one piece has a work-hardened fold that won’t close predictably a second time. Treat every double ear clamp as single-use and keep spares on the bench. If a joint is opened regularly, fit a reusable worm gear or lined clamp.
Where on the barb should the ear clamp go?
Place the band on hose that lies over the barb body, just behind the outermost ridge and a few millimetres back from the fitting shoulder. It should not sit on the cut end of the hose, beyond the barb on unsupported hose, or on top of a ridge. Mark the insertion depth before pushing the hose on, and the right position becomes easy to find and easy to inspect.
Is soapy water safe to use when pushing a hose onto a barb?
For most rubber and PVC hoses, plain water or a mild soap solution is a safe assembly aid and far better than oil, which can swell some hose compounds. Use as little as you can so the hose doesn’t creep off later. On potable water, food or medical lines, use only the lubricant the hose maker and your hygiene rules allow, which is often just clean water.